pappo pappo Hi, i have installed openelec on my orange pi plus 2e. I installed Tvhead, but when I scan all the Muxes have failed (sorry for my bad english). I am desperate. I have attached the video. Thank you guys. Pappo
Saen Acro Is tuner work? dmesg |egrep "firmware|dvb|frontend|usb" tree /dev/dvb or if IPTV then limit to1 session
pappo pappo OpenELEC (community) Version: devel-20161026220508-r23113-g64b34b3 OpenELEC git: 64b34b380c3102239acb8306b5f17020979793e8 OpenELEC:~ # dmesg |egrep "firmware|dvb|frontend|usb" [ 0.176170] usbcore: registered new interface driver usbfs [ 0.176170] usbcore: registered new interface driver hub [ 0.176170] usbcore: registered new device driver usb [ 1.699007] usbcore: registered new interface driver usb-storage [ 1.710875] usbcore: registered new interface driver ums-alauda [ 1.717490] usbcore: registered new interface driver ums-cypress [ 1.724207] usbcore: registered new interface driver ums-datafab [ 1.730922] usbcore: registered new interface driver ums_eneub6250 [ 1.737812] usbcore: registered new interface driver ums-freecom [ 1.744531] usbcore: registered new interface driver ums-isd200 [ 1.751150] usbcore: registered new interface driver ums-jumpshot [ 1.757945] usbcore: registered new interface driver ums-karma [ 1.764481] usbcore: registered new interface driver ums-onetouch [ 1.771333] usbcore: registered new interface driver ums-realtek [ 1.778043] usbcore: registered new interface driver ums-sddr09 [ 1.784692] usbcore: registered new interface driver ums-sddr55 [ 1.791350] usbcore: registered new interface driver ums-usbat [ 1.960050] usb 5-1: new low-speed USB device number 2 using sunxi-ohci [ 1.970041] usbcore: registered new interface driver usbhid [ 1.976224] usbhid: USB HID core driver [ 2.210880] generic-usb 0003:15D9:0A4C.0001: input,hidraw0: USB HID v1.11 Mou se [ USB OPTICAL MOUSE] on usb-sunxi-ohci-1/input0 [ 49.300110] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 49.512074] dvb-usb: found a 'ITE 9135(9005) Generic' in cold state, will try to load a firmware [ 49.516958] dvb-usb: downloading firmware from file 'dvb-usb-it9135-02.fw' [ 49.860598] dvb-usb: found a 'ITE 9135(9005) Generic' in warm state. [ 49.861059] dvb-usb: will use the device's hardware PID filter (table count: 31). [ 50.184601] DVB: registering adapter 0 frontend 0 (ITE 9135(9005) Generic_1). .. [ 50.189741] rc1: IR-receiver inside an USB DVB receiver as /devices/platform/ sunxi-ehci.3/usb3/3-1/rc/rc1 [ 50.189760] dvb-usb: schedule remote query interval to 250 msecs. [ 50.189788] dvb-usb: ITE 9135(9005) Generic successfully initialized and conn ected. [ 50.189945] usbcore: registered new interface driver it913x [ 50.267250] DVB: adapter 0 frontend 0 frequency 0 out of range (51000000..168 0000000) OpenELEC:~ # tree /dev/dvb -sh: tree: not found OpenELEC:~ #
Saen Acro There is something wrong with this device. (51000000..168 0000000) 51Mhz - 168Mhz Your muxes are on out of supported by device frequency try with other firmwaredvb-usb-it9135-02.fw
pappo pappo Sorry for my ignorance. How can I manually install the FW on OpenELEC? I have the "dvb-usb-it9135-02.fw" file. Thank you.
pappo pappo When I try to delete the existing file from "/lib/firmware" I get this message: OpenELEC:/lib/firmware # rm -f dvb-usb-it9135-02.fw rm: can't remove 'dvb-usb-it9135-02.fw': Read-only file system
