Well, I would like to - but for me it´s currently not working.
I get this on startup:
> ...
> 2014-01-15 18:31:07.627 [ INFO] AVAHI: Service 'Tvheadend' successfully established.
> 2014-01-15 18:31:08.253 [ ERROR] linuxdvb: STV090x Multistandard : DVB-S #0 - failed to tune [e=Das Argument ist ungültig]
> 2014-01-15 18:31:08.253 [WARNING] mpegts: 11158V - failed to start, try another
> 2014-01-15 18:31:08.253 [ INFO] mpegts: 11158V - starting for 'epggrab' (weight 1)
> 2014-01-15 18:31:08.253 [ INFO] mpegts: 11158V - tuning on STV090x Multistandard : DVB-S #0
> 2014-01-15 18:31:09.915 [ ERROR] linuxdvb: STV090x Multistandard : DVB-S #0 - failed to tune [e=Das Argument ist ungültig]
> 2014-01-15 18:31:09.915 [WARNING] mpegts: 11158V - failed to start, try another
> 2014-01-15 18:31:09.915 [ INFO] mpegts: 11158V - starting for 'epggrab' (weight 1)
> 2014-01-15 18:31:09.915 [ INFO] mpegts: 11158V - tuning on STV090x Multistandard : DVB-S #0
> ...
And tvheadend hangs here...
Matthias Strack
Config error?
Can you post a screenshot from your adapter settings?
Have you tried seifes port, its still based on 3.5, but it works for me
->
https://github.com/seife/tvheadend
Dirk Leber
Seifes port worked so far, but I like to use current git.
Config error - maybe, but not from what you see in the config...
I changed the tuner config while still in initial scan - maybe that was a bad idea.
Wrong frequency values (S2CMD 03) for the DiSEqC sequence was the problem, but I don´t know why.
I made a fresh setup - it´s still running and currently mapping channels...
Matthias Strack
All channels found?
My problem is, no data received on most transponders, finds only french channels,and bibel tv ;>
Dirk Leber
Mapping will take some time, even with 4 tuners...
Currently 1203/1962 (19.2E + 13.0E)
Mapped 98, Ignored 1008, Failed 97
I will report.
Adam Sutton
Guys,
I would like to get to the bottom of this, clearly something has gone wrong during the various migrations that have taken place to get the code into master.
Unfortunately I'm not very familiar with the code, the only changes I made were some basic structural (and config) ones. Though those could certainly have caused issues.
A trace log would be really useful, start with these options:
--trace mpegts,linuxdvb,diseqc,en50494 -l tvh.log
and then paste those logs. I'll try and ask the guy that did the port to master when I see him on IRC.
Adam
Dirk Leber
Ok, mapping complete - 150 got mapped (haven´t checked them yet).
One thing is that I had to retune an other receiver (using scr channels 0 to 2) to get an picture there again (also stopped tvheadend).
After restarting tvheadend, I got the same error from yesterday (see log).
Commands like "S2CMD 03 => 0" or "S2CMD 03 => 4294966546" don´t look good to me...
And one more thing: after changing an adapter to unicode, you have to press save to activate the options (and to change the subitem). This collapses the treeview and you have to open the whole tree again. Any chance to keep the treeview expanded?
Matthias Strack
TVH Log attached.
@Dirk same error here after restarting TVH.
2014-01-16 07:59:37.317 [ ERROR] linuxdvb: Conexant CX24116/CX24118 : DVB-S #0 - failed to tune [e=Das Argument ist ungültig]
<<
Adam Sutton
Guys,
can one of you report this as a bug. It's possible I'll get distracted and forget about this thread, but if its in as a bug I'm more likely to remember it!
Adam
Matthias Strack
Done
