Mark Clarkstone wrote:
> Gabor Mohacsi wrote:
> > Hello,
> >
> > I just found this topic, I received my Hauppauge QuadHD, and I try to make it work, unfortunately with out any success. I downloaded the firmware, Kernel version 4.93
> > dmesg:
> > 14.2/sound/card0/input8
> > [ 19.508152] ppdev: user-space parallel port driver
> > [ 19.568100] input: HP WMI hotkeys as /devices/virtual/input/input9
> > [ 19.796659] cx23885 driver version 0.0.4 loaded
> > [ 19.797050] CORE cx23885[0]: subsystem: 0070:6a28, board: Hauppauge WinTV-Qua dHD-DVB [card=56,autodetected]
> > [ 20.138435] tveeprom 8-0050: Hauppauge model 166200, rev B4I6, serial# 403586 7918
> > [ 20.138436] tveeprom 8-0050: MAC address is 00:0d:fe:8e:75:0e
> > [ 20.138437] tveeprom 8-0050: tuner model is SiLabs Si2157 (idx 186, type 4)
> > [ 20.138438] tveeprom 8-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
> > [ 20.138439] tveeprom 8-0050: audio processor is CX23885 (idx 39)
> > [ 20.138440] tveeprom 8-0050: decoder processor is CX23885 (idx 33)
> > [ 20.138441] tveeprom 8-0050: has no radio, has IR receiver, has no IR transmi tter
> > [ 20.138442] cx23885[0]: warning: unknown hauppauge model #166200
> > [ 20.138442] cx23885[0]: hauppauge eeprom: model=166200
> > [ 20.138443] cx23885_dvb_register() allocating 1 frontend(s)
> > [ 20.138444] cx23885[0]: cx23885 based dvb card
> > [ 20.225439] i2c i2c-8: Added multiplexed i2c bus 11
> > [ 20.225441] si2168 8-0064: Silicon Labs Si2168-B40 successfully identified
> > [ 20.225442] si2168 8-0064: firmware version: B 4.0.2
> > [ 20.238491] si2157 9-0060: Silicon Labs Si2147/2148/2157/2158 successfully at tached
> >
> > and on the tvheadend I having this when I try to scan the muxes:
> >
> > 2017-02-13 12:36:06.189 subscription: 015D: "scan" subscribing to mux "394MHz", weight: 6, adapter: "Silicon Labs Si2168 : DVB-C #0", network: "magyartv", service: "Raw PID Subscription"
> > 2017-02-13 12:36:10.064 linuxdvb: Unable to provide BER value.
> > 2017-02-13 12:36:10.064 linuxdvb: Unable to provide UNC value.
> >
> > and this:
> > 2017-02-13 12:36:16.004 subscription: 0161: "scan" unsubscribing
> > 2017-02-13 12:36:16.005 mpegts: 762MHz in magyartv - tuning on Silicon Labs Si2168 : DVB-C #0
> > 2017-02-13 12:36:16.008 subscription: 016B: "scan" subscribing to mux "762MHz", weight: 6, adapter: "Silicon Labs Si2168 : DVB-C #0", network: "magyartv", service: "Raw PID Subscription"
> > 2017-02-13 12:36:16.009
mpegts: 121MHz in magyartv - scan no data, failed
> >
> > Can you please help me, what do I do wrong?
> > Thanks and regards.
> > Gabor
>
> "scan no data, failed" means that nothing was found on that frequency. You need to make sure that you're entering all the details correctly - especially Symbol rate, you sometimes need to add three additional zeros to it. Use w_scan to determine the available frequencies, you usually only need one, tvheadend should find the rest if your provider uses NIT.
Hi Mark,
Thanks for your reply.
I having this from w_scan:
Info: using DVB adapter auto detection.
main:3904: FATAL:
*** NO USEABLE CABLE CARD FOUND.
***
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.
but how it's possible I have no usable cable card? On dmesg I can see the tuner card,
I see it on tvheadend as well. I placed the b40 firmware and I upgraded the kernel to 4.93
I tried to change the values and scan, and I checked the correct values on the TV provider's website.
Sorry if I make fatal mistake, unfortunately Im not linux expert...