Hi!
I've installed tvheadend from the deb-package on this page. To this, I'm running a WinTV PVR USB2. However, when logging on to the admin interface there's no adapter shown in the list.
I've read somewhere where one hade a similiar problem that Tvheadends requires a MPEG-encoder, but the WinTV PVR USB2 has one (http://registration.hauppauge.com/webstore/hardware2.asp?product=pvrusb2).
The HTS is user is in video group, and I've run chmod a+rw /dev/video0 (which shows up, so the adaptor works. I figured at least.)
Output of dmesg:
zyber@tvbackend:/dev$ dmesg | grep pvr
[ 6.164163] pvrusb2: Hardware description: WinTV PVR USB2 Model 24xxx
[ 6.165014] usbcore: registered new interface driver pvrusb2
[ 6.165017] pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner
[ 6.165031] pvrusb2: Debug mask is 31 (0x1f)
[ 7.385789] pvrusb2: Device microcontroller firmware (re)loaded; it should now reset and reconnect.
[ 8.634223] pvrusb2: Device being rendered inoperable
[ 12.447634] pvrusb2: Hardware description: WinTV PVR USB2 Model 24xxx
[ 12.502051] pvrusb2: Device has newer IR hardware; disabling unneeded virtual IR device
[ 12.502055] pvrusb2: Binding ir_rx_z8f0811_haup to i2c address 0x71.
[ 12.502090] pvrusb2: Binding ir_tx_z8f0811_haup to i2c address 0x70.
[ 12.616376] cx25840 0-0044: cx25843-24 found @ 0x88 (pvrusb2_a)
[ 12.659415] pvrusb2: Attached sub-driver cx25840
[ 12.714742] pvrusb2: Attached sub-driver tuner
[ 12.717808] wm8775 0-001b: chip found @ 0x36 (pvrusb2_a)
[ 12.742876] pvrusb2: Attached sub-driver wm8775
[ 12.792495] pvrusb2: Attached sub-driver tuner
[ 16.278047] pvrusb2: Supported video standard(s) reported available in hardware: PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K
[ 16.278050] pvrusb2: Mapping standards mask=0xff00ff (PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K1/L/LC)
[ 16.278051] pvrusb2: Setting up 20 unique standard(s)
[ 16.278053] pvrusb2: Set up standard idx=0 name=PAL-B/G
[ 16.278054] pvrusb2: Set up standard idx=1 name=PAL-D/K
[ 16.278056] pvrusb2: Set up standard idx=2 name=SECAM-B/G
[ 16.278057] pvrusb2: Set up standard idx=3 name=SECAM-D/K
[ 16.278058] pvrusb2: Set up standard idx=4 name=PAL-B
[ 16.278059] pvrusb2: Set up standard idx=5 name=PAL-B1
[ 16.278060] pvrusb2: Set up standard idx=6 name=PAL-G
[ 16.278061] pvrusb2: Set up standard idx=7 name=PAL-H
[ 16.278062] pvrusb2: Set up standard idx=8 name=PAL-I
[ 16.278063] pvrusb2: Set up standard idx=9 name=PAL-D
[ 16.278064] pvrusb2: Set up standard idx=10 name=PAL-D1
[ 16.278065] pvrusb2: Set up standard idx=11 name=PAL-K
[ 16.278067] pvrusb2: Set up standard idx=12 name=SECAM-B
[ 16.278068] pvrusb2: Set up standard idx=13 name=SECAM-D
[ 16.278070] pvrusb2: Set up standard idx=14 name=SECAM-G
[ 16.278071] pvrusb2: Set up standard idx=15 name=SECAM-H
[ 16.278073] pvrusb2: Set up standard idx=16 name=SECAM-K
[ 16.278075] pvrusb2: Set up standard idx=17 name=SECAM-K1
[ 16.278076] pvrusb2: Set up standard idx=18 name=SECAM-L
[ 16.278077] pvrusb2: Set up standard idx=19 name=SECAM-LC
[ 16.278079] pvrusb2: Initial video standard auto-selected to PAL-B/G
[ 16.278085] pvrusb2: Device initialization completed successfully.
[ 16.278564] pvrusb2: registered device video0 [mpeg]
[ 16.278867] pvrusb2: registered device radio0 [mpeg]
zyber@tvbackend:/dev$ dmesg | grep tv
[ 16.278035] tveeprom 0-00a2: Hauppauge model 24029, rev E189, serial# 8665800
[ 16.278038] tveeprom 0-00a2: tuner model is TCL MFPE05 2 (idx 89, type 38)
[ 16.278039] tveeprom 0-00a2: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
[ 16.278041] tveeprom 0-00a2: audio processor is CX25843 (idx 37)
[ 16.278042] tveeprom 0-00a2: decoder processor is CX25843 (idx 30)
[ 16.278043] tveeprom 0-00a2: has radio, has IR receiver, has IR transmitter
And syslog with tvheadends output:
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: pvrusb2 WinTV PVR USB2 Model 24xxx usb-0000:02:02.0-1 capabilities: 0x01070001
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #0: 0000000000000005 PAL-B/G, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #1: 00000000000000a0 PAL-D/K, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #2: 0000000000050000 SECAM-B/G, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #3: 0000000000120000 SECAM-D/K, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #4: 0000000000000001 PAL-B, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #5: 0000000000000002 PAL-B1, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #6: 0000000000000004 PAL-G, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #7: 0000000000000008 PAL-H, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #8: 0000000000000010 PAL-I, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #9: 0000000000000020 PAL-D, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #10: 0000000000000040 PAL-D1, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #11: 0000000000000080 PAL-K, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #12: 0000000000010000 SECAM-B, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #13: 0000000000020000 SECAM-D, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #14: 0000000000040000 SECAM-G, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #15: 0000000000080000 SECAM-H, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #16: 0000000000100000 SECAM-K, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #17: 0000000000200000 SECAM-K1, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #18: 0000000000400000 SECAM-L, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Standard #19: 0000000000800000 SECAM-LC, frameperiod: 1/25, 625 lines
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Input #0: television (Tuner), audio:0x0, tuner:0, standard:0000000000000000,
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Input #1: composite (Camera), audio:0x0, tuner:0, standard:0000000000000000,
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Input #2: s-video (Camera), audio:0x0, tuner:0, standard:0000000000000000,
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Input #3: radio (Tuner), audio:0x0, tuner:0, standard:0000000000000000,
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Format #0: MPEG1/2 [] (compressed)
Sep 9 14:53:28 tvbackend tvheadend[7981]: v4l: /dev/video0: Device lacks MPEG encoder, device skipped
Sep 9 14:53:28 tvbackend tvheadend[7981]: dvr: Creating new configuration ''
Sep 9 14:53:28 tvbackend tvheadend[7981]: CSA: Using SSE2 128bit parallel descrambling
Sep 9 14:53:28 tvbackend tvheadend[7981]: START: HTS Tvheadend version 3.0 started, running as PID:7981 UID:106 GID:44, settings located in '/home/hts/.hts/tvheadend', dataroot: /usr/share/tvheadend
Why does tvheadend says that there's no mpeg encoder? Have I missed something?
Thanks in advance!
Zyber
